Showing posts with label toy. Show all posts
Showing posts with label toy. Show all posts

Thursday, February 2, 2023

Animated toys

 I received a book on how to make animated toys a few years back. It was something that I have wanted
to try and different from the vehicles I have been making. I was hoping that this would help me into
new design ideas. I compliment the author and the work he has done to make these toys. The plans
were done well and easy to follow.
I really liked the concept of the toys, but I did not like how they went together. There were a lot of small
parts and purchased parts that needed to be cut down. I felt that the parts were really small for the
target kid age. This may be the toys that I decided to make. The dinosaurs had a lot of parts and were
on the more complicated side. Looking back the basic toys would probably be just as fun or better than
the more complicated ones. I will probably not make any more of the multiple linkage toys. From an
engineer standpoint, I can appreciate the design of these toys. I may make some of the simpler toys at
another time. These toys do take a lot of different thickness of wood which makes it a little more
challenging to plan.





Thursday, August 25, 2022

Buildable Toys for a Church






 I was contacted by a church in the south about making kits for youth to build at their youth camp. Of course I said yes and under costed the project. It is a little more difficult to mass produce build your own projects. I didn’t have a belt sander to make everything flat and smooth. 

They requested 4 projects and 15 of each. I could not do all the toys the person wanted, because I did not have the time to redesign so they can be put together by kids. They turned out all right. I don’t know how easy they were to assemble, but I got good feedback from them.

Saturday, May 9, 2020

Ping Pong Ball Guns





In this time of quarantine and isolation, it has been hard to keep the kids entertained, busy and learning.  I have been trying to teach the scientific process and working though problems to a solution.  I am an engineer by career and degree, so these attributes are important to me.  I saw a plan to make a rubber band gun in a magazine.  I didn’t think it would be too hard to create experiments that would entertain the kids and allow them to look at data to come up with a solution.  This project was not as easy as I thought it would be.  Here are some of the highlights that I learned.
Setup:  I created a board with 11/32” holes spaced at ¾” from the centerline.  I was able to get 10 sets of holes.  I drilled 7/36” holes on the centerline and spaced them 1” apart.  I drilled 3/16” holes in a clothes pin 1” apart and put in 3/16” dowels.  Created spacers in 3/16” thick material.  Sorry, I did not take pictures of the test board.

Experiment 1
What height should the rubber band be placed to have optimal distance?  We set the rubber band holder and the clothes pin distances as constant and raised the clothes pin by 3/16” spacers. (This was the thickness of scrap I had. 1/8” would also work.)  My youngest helps with this part.  We had a sample size of 6 at each height.  The neat thing about this experiment was there was definite height that was the optimal height.

Experiment 2
What should the space between the pins that hold the rubber band be?  We set the height at the optimal height from the last experiment.  Unfortunately, we could not set the clothes pin distance constant.  As the pins get closer together the potential energy of the stretched rubber band is decreased.  Yes, I did consider this and had a solution, but I did not do it.  To compensate we moved the clothes pin back after we moved the rubber band pins in three times.  This did muddy the results.  There was a couple of spaces that did create very consistent results.  I did a sample set of 10 on this experiment because the middle child, who likes science, was helping me.  That was not a good idea because he had about the same attention span of the younger child.  Should have kept at 6 samples.

Experiment 3
How far back should the clothes pin be?  The rubber band pins and clothes pin height remained constant.  We were not too concerned with distance and consistency on this experiment.  We just wanted to see what distance the clothes pin could hold the rubber band without misfiring. 
Results

So, with all the data and observations, we determined the best dimensions for a rubber band gun.  I took some clip art and blew up the back section to trace patterns.  The kids and I traced and cut out the guns.  Attached the cross piece to hold the rubber band and the clothes pin.  The kids were excited and the wife not so much.  The oldest decided the ping pong balls were not that impressive so he has tried shooting other things. 

Here are some of my observations on this process.  Some are design related and others scientific.
  • Bernoulli's principle – It was actually pretty cool to see this in action on the height of the clothes pin experiment.  Depending on the height of the rubber band it would put a top or bottom spin on the ball.  Top spin would make the ball just drop.  The bottom spin would cause the ball to float.  It made sense the optimal height was just below half the diameter the ball.
  • Eight-inch rubber bands degrade quickly.  It only takes 5-10 stretches of a rubber band before it stretches over 8”.  We did account for this and change the rubber band for each experiment.  Where this proved to be difficult was experiment 2.  The distance that gave the most reliable results was when the rubber band stayed in place on the pins.  When the rubber band did not have the tension to keep it in place the results were not as consistent.  This was because we would have to put the rubber band after each shot.  A little high gave the ball more top spin and a little low and we would have more bottom spin.  On the guns we ended up wrapping the rubber band around each pin once to hold it in place
  • Ergonomics and gun holding is a pain to figure out.  The trigger finger is not the index finger but the thumb.  That makes it difficult to hold.  It was a lot of cutting.  Cardboard only helps so much because it is only 1/8” thick. 
  • Angling the clothes pin does not help a lot.  It actually could create a problem if angled too much; the rubber band might not fire.
  • Clothes pins are cheap and break easily.  This could be because I made them not well supported and replaceable. 
  • These guns are super inaccurate and unreliable, but fun and sort of safe to shoot. (doesn’t leave as big of a mark as the rubber band gatling gun; not speaking from experience)
It was a lot of work just for a two-piece wood project.  Worth it for the kids and glad they had fun.  Sorry no plans for this one.  It is better to make your own on this one.


Wednesday, January 15, 2020

Toy Cars



This is the last of the toys planned for this year.  I was honestly scared that I would not get them completed in time for the upcoming craft fair. I only had about 6 weeks to get everything cut and finished.  It is amazing how productive I was when under a hard deadline.  That was probably one of the bigger take away lessons from this project.  Planning what was needed to be done on Saturday and what I could do in the evening during the week.  Here is the basic run down of each of the four cars.
Race Car
This was a layered car and pretty straight forward when it comes to the design.  The first challenge that I was faced with drilling the wheels and making sure that they all lined up.  One important rule of toy making is that all wheels have to roll.  They don’t have to be centered, but they need to roll.  What I did was drill holes on only one of the side pieces.  When body was glued together and the bottom sanded flat, I used the drilled holes as a guide and drilled through the entire body of the car.  The other design change that I did was remove the small front piece.  There was a little piece in the front for a front air foil.  It was too small and I chose to remove it entirely.
I did make one huge mistake.  I installed all the small pieces between the wheels upside down.  It works but I realized it on the last four that I was assembling.  I added the radius to help hide the error.  I like the radius but the error still is obvious for me.
I like how it turned out and the simplicity of the design.  It looks really nice when adding two difference colors of wood

Jeep
Jeep owners love jeeps.  I am not a jeep owner but I cannot argue with the rugged appearance it has and it is an iconic vehicle that kids can relate to.  So I made one.  The design is pretty straight forward but not easy to assemble.  The engine and back need to be all assembled together, but the engine has an angle that is cut into it that is easier to cut and sand before assembly.  I had to make some fixtures so that all the pieces lined up.  That was the hardest part of the build, besides sanding.  Sanding all the cars was a chore.

Flat Bed Truck
The last two were a little more complicated when it came to making multiples.  The concern was matching up the roof dowel holes with the holes in the sides. I needed to drill the holes before I cut out any of the details in the sides.  I ended up taping the sides and back together.  I also numbered the top and the sides so I knew which parts went together.  Then taping the top to the sides and back.  After marking out the holes, I drilled them.  I thought I was being clever and putting the numbers on the inside surface.  That backfired when I drilled through all the numbers I marked.
After doing the dry fit, the wheels just did not look right.  They were the 1¼” diameter and looked small.  I was able to adjust them and increase the wheel diameter to 1½”.  It looks much better now and I have updated my drawings.

Model T
I did the holes in the roof the same way as the flatbed truck.  This time I numbered them on the side rather than where I drill the holes.  It was much easier to identify the parts to each car.  I will have to say the treaded wheels look a little odd on the Model T.  They do sell a spoke wheel that would probably look better, but I did not want to introduce a new wheel into my inventory.
Overall I enjoyed the projects.  I really like how the different wood species bring out different colors.  I am thinking about scaling them up to be a larger size in thicker wood.  Not sure how they would look, but I am thinking next year.




Sunday, June 16, 2019

Build and Grow Planes

  The next set of toys in the build and grow series is the planes.  I had a lot of fun designing them.  As usual, they were a lot bigger in my mind than in real life.  They were a lot of fun to build even though they were on the smaller side.  I had to make some concessions with my design criteria.  I needed to introduce some nonstandard thicknesses.  The wings just did not look good on ¾” material so I reduced it down to 5/16” but ¼” will also work. 
There are four different planes and I will go into each one and some of the difficulties and things that I liked about them.  They all had all there difficult parts and it was fun working through them.  There are a couple of things that I did different with this design.  First was that I printed the patterns on card stock so that I could trace the patterns on the wood.  The second is that I am batching several of them out in different woods.
The Helicopter
It seems like a pretty basic design until I realized the cuts on two faces and the holes that I needed to drill.  So I marked out the pattern and the holes on the body.  Cut all the lines from both directions leaving about ¼” between the two cuts so that I do not have to tape the part back on.  After the body was cut out, I finished the cuts on the sides.
The next challenge was the small parts.  I realize quickly that there were a lot of parts that I was not comfortable cutting on the table saw or chop saw. I used the band saw a lot on these parts. I am now looking into an 1/8” blade for the band saw.  The skids on the landing platform I changed after I cut them out.  They were originally going to be doweled.  They are no longer that way.  There really was no reason to do so because it is face grain to face grain bond.  I also have widened them a little from the original design.


The Jet
This is pretty much a scroll saw and sanding operation.  There are small pieces but I liked how well it came out.  It is definitely the easiest of the planes to make.







The Bi-Plane.
This was another project where it was helpful to have the band saw around.  The only thing that I needed to keep together was the wings. I drilled the top and bottom wings strut holes taped together since I was making 12 of them.  I marked the top and bottom of each.  That face was sanded after everything was assembled.




The Prop Plane
This one was modeled after the first plane that I did.  The wings have a 5 degree tilt on them.  I was pretty confident that this plane would not be a huge problem.  I did the same thing with the multiple cuts as I did on the helicopter body.  I then cut the taper on the bottom.  When it came to putting the groove for the wings in, I had a problem.  The part was much smaller than the original design.  I needed some way to cut this groove safely.  I used a miter gauge and a sacrificial extension.  Looking back, I should have put the five degree angle on the extension.  I had a problem keeping the bottom flat because it was small and liked to rotate.  This did not give me a consistent groove depth over the part.
I liked how they turned out.  I was different using harder woods of half of them.  This is why I was grateful for the band saw.  I could do them with the scroll saw, but it would have taken a lot longer.

Build and Grow Boats



I will have to admit, these are not as exciting of a build as the planes. They were fun to build and will be just as fun to play with.  I made 12 of each of these; half were out of poplar and half other woods.  I did have to bring in 1/2" thick lumber to make the proportions look correct.

Tug Boat
This is a smaller version of the original one that I have made in the past.  I incorporated the cutout of the deck to be the top of the cabin.  Hardest part was the small pieces which I use the band saw and the sander to safely cut.







The Rescue Boat
The hardest part of this boat was the cabin.  I wanted the front to be tapered and that was easy.  The problem was cutting both the top and bottom so they had the same radius but one was flat and tapered on the top.  I think they came out and looking good.  I did screw up the color mixes on the hard woods but it turned out.





The Ferry
This is the boat where all the learning happened. The design was not all that difficult.  The waterwheel was the part that caused some thought on assembly and materials. I learned that all dowels are not the same.  I purchased a dowel that did not have all straight grain.  part of it had the grain at about a 60 degree angle.  Normally this would not create a problem, but the dowel is not supported through its length.  When putting the other side of the waterwheel on it would break the dowel.  The other problem with the dowels was the inconsistent diameter.  The thicker ones would split the waterwheel.  After all this I like the way they turned out.









Monday, May 20, 2019

The Battle Ax



A friend asked me to make a toy battle ax for her son.  I think I will stick with the toy cars and kid furniture.  Toy weapons are different and I will explain a little later. 
As with most projects I wanted to try something new.  This was going to be the handle.  I was going to try to do a para cord wrap.  The ax is pretty straight forward.  It is an oak handle that is about 1 ½” square.  The blade is two pieces of beech and measures 20” across.  I made a template of blade and cut them out.  The edge is sanded down with a ¼” flat so it is not sharp.  I took a wide board and put a dado in it the width of the narrow part of the blade and ½ the thickness.  By ripping the board in half and gluing it together I had the mortise to put the blade in.  I narrowed the handle with a spiral bit and the router.  Just a plug for Triton, I really like their router set up with the work center.  It will be sad when my son collects his winnings. 
Once I had all the parts profiled the way I wanted, I dry fitted it together.  There was one area that was a little tight.  I was removing the blade of the ax and it came out of the mortise and the corner hit my finger next to the nail.  It removed the flesh that was next to the nail.  This is worst woodworking injury that I have sustained so far.  It kind of put a damper on the rest of the day.  My wife asked if I need to go to urgent care.  My response was that there was nothing to sew back together.  It actually has been healing quickly.  It is just sensitive.
The handle was fun to do.  I think it came out ok.  I could not get the top knots to look good, but the handle I liked.  My kids saw it and wanted to hold it and I let them.  It was too heavy for my youngest.  My oldest (9 years old) swung it and I said that is enough and I will take it now.  It seriously scared me.  The ax has some heft to it.  I would liken it to a bat with a dull blade attached.  The blade will break bones before it breaks.  I did round off the corners that caused my injury but it still scared me.  When making toy weapons, I think I just make blunt weapons.
My kids now want one, and they will not get one. 

Sunday, November 11, 2018

Little Vehicle Series


I decided that I needed to expand the little vehicle series by three more.  This makes it an even ten vehicles.  The ambulance was a simple design, my son wanted a cement truck, and I wanted to do a forklift.  That is where the designs came from.
First, the easy one.  The ambulance is pretty straight forward and can be made into a box truck.  There really is not much too the design.
The forklift was much more challenging.  The biggest struggle was the proportions.  It was either too big, too long or just did not look right.  I wanted something were I did not have to use a scroll saw and could be cut out with a table saw and chop saw.  Overall, I am happy how it turned out.  I will say, having a hand plane really helped out on flattening the dowel and adding the profiles.
The impossible request was the cement truck.  I could not figure out how I was going to make it.  I do not have a lathe which means that I was going to use a dowel.  I was not sure how the bucket was going to be attached and then there was the size.  I first established my constraints, the chassis was 2 ½” wide and max 4.5” long.  The largest dowel I can buy was 2” at the big box store.  This is why I love to design in the 3d modeling world with good software.  I learned quickly that I could match angles with the barrel supports and using constraints, I could determine the angle and the distance that would result in measurements that were 1/8” or larger.  Then I had the structural concerns.  I doweled a lot of the pieces.  I did not worry about how I was going to make all the parts until that time came, and I procrastinated it.
Toughest part was the barrel.  I ended up setting my band saw at 45 degrees and putting in stop blocks.  It turned out easier than I expected and safer than a router which was my first thought.  I then needed to do the same setup with the belt sander.  This also took time to finish because I needed to tape off a lot of parts.  It came out well and my son is happy.






Tuesday, July 10, 2018

Little Vehicle Train


In addition to the cars I also made a train for this series.  Same design principles as the rest of the series.  It was basic enough to make several and just enough to challenge to learn and try new things.
The main learning came from the large dowels.  I needed to put a flat surface on them.  The last time I did this I attached it to a board and ran it through a band saw.  This worked ok. It did not remain as flat after I sanded away the tooling marks.  This time I had a plane, but I did not have a sturdy workbench or reference plane.  That is where the table saw came in.  it is a flat surface with a ripping fence.  It worked great.
The holes on the chassis for the cars also proved to be a challenge.  One is ¼” and the other is 9/32” both should be drilled at the same time.  I really did not want to guess which side to put the groove.  I ended up only drilling part way through.  This way the side that was not drilled, was the side I grooved.
I really liked how the train turned out.  It is 22 inches long and about 4 ½” tall.

Wednesday, July 4, 2018

Little Vehicle Series

So I redid the idea of the build and grow and added a couple of more cars.  I tried to make them where kids can pound in the nails.  Honestly, that took way too much time.  Each unit had to be drilled together and packaged together.  I really did not trust myself to mix parts.  The precision was too much for the equipment I was using.  I turned and made a bunch how I would make them without nailing them together.  Here are some of the things that I wanted to do with this project.

First is the design.  This was all done without the need of a scroll saw.  This is unique for my toys.  The tools I used were a table saw, miter saw, band saw, drill press and belt sander.  I tried to limit the number or rip widths I used so that I could just rip a bunch of material.  This came in handy since I was making ten of each car. Everything but the cab is made from or can be cut from ¾ inch material and ¼ inch plywood.

The ease to make a lot at once.  I wanted to be able to make these in batches.  This was a reason for limiting the number of rip widths.  I also tried to standardize on the profiles so multiple parts can be made with the same groove or angle.  I tried to keep the drilling standard as much as I could but was not as successful.  This kept setups to a minimum and made it easy to batch out a lot of parts at a time.  I will admit drilling 140 holes in cabs did get a little boring (pun intended). 
Durability and Safety.  This is always important to me and the toys I make.  I want them to be played with and not be destroyed in a couple days.  My design limitations were the wheels needed to be at least 1 ¼ inches in diameter (choking hazard).  The toy needed to be big enough that little hands could still grab it and handle it.  It needed to be able to endure rough play.  There are a lot of glue surfaces for each part.  I am not a huge fan of plywood but it was the best material to use for the thin parts.  Plywood is a little more resistant to breaking when in thinner stock than wood.

Price.  I don’t usually talk about price because that has never been a focus.  This time is was.  I wanted the price to be $15 and still make some sort of profit.  I am not going to disclose how much each of the toys cost to make.  Just know that if I put in my labor I would be significantly higher than the $15 limit.  I did figure out the cost of each vehicle to the penny.  They also fall below the $15 mark.  The reason for the price cap is craft fairs.  The lower priced items sell faster than the higher priced ones.  Last year I had a lot of high priced items; this year I am changing it up.

Drawings. I draw everything out in a 3d CAD system.  These were done in Solid Works.  This was more of a learning experience for me.  I was able to design my own drawing template and learn more about Solid Works.  I am not sure how I am going to sell the drawings yet.  I am hoping to submit a couple to some magazines to see what happens.  I have the option to sell them as a complete set or individually.  I may try to mix up an offer on them.  Not sure how Etsy will handle an offer.  More learning on my end.

Bill of materials. With doing multiple sets I wanted to know how much I needed of everything.  This is where everything came together or fell apart and it did both.  I created an excel workbook with all the information in it about each of the projects.  Added a multiplier to figure out how much of everything I needed.  It calculated everything from linear feet of each rip width to purchased components.  It even spit out my cost.  I even figured out how to convert to fractions of a foot.  I know inches would have been better but I stopped at fractions.  It is setup so that a person can put in the number of each toy they would like to make and it will tell you the linear foot of each rip width, quantity of all the purchased parts, the length of dowel required.  It will also factor in the kerf cut and yield.  If you purchase any of these plans, email me and I will send you the excel sheet.  I will delete the plans that have not been purchased.  Sorry, if you have the dimensions of the parts you have the plan for these toys.
The build was pretty straight forward.  Did not have very many problems with the exception to my excel sheet.  I had a calculation error for the length of dowel needed.  I have fixed that and it works fine.  I have added a police cruise to the lineup.  This actually has the parts that I am looking for to make a semi-truck line.  This is probably going to happen next year though.









Monday, June 25, 2018

Jeep




After several months I finally finished the Jeep.  To be honest, I am a little disappointed in the design.  I will need to redesign if I am going to sell the plans.  The top portion was fragile and broke with putting in the dowel cross members.  The fenders were all right but were more challenging than I would like to admit.  The wheels seem too small for the size of the vehicle.  I would have to lose the back spare if I was to grow them.
I do like the overall body of the Jeep.  The design did look good on the computer.  I like the taper on the engine but it made the front fenders difficult to make.  I also thought the seats and the open back was a nice design detail that came out really well.
The project was fun even though I was not all that happy with it.  This is the fun part of prototyping a project, now I can redesign it better.

Saturday, June 16, 2018

Puzzles





Early this year, I decided to make a bunch of puzzles.  I had a lot of ¼” and 1/8” ply wood so the plan was to put them on boards.  I painted 5/8” thick poplar on one side with the primary and secondary colors.  On the other side I painted them black.  Anyone that has done a wood puzzle knows that it is a pain because there is no real indication which side is the top.  Then I adhered all the patterns to the colored board.  I cut them all apart making sure that I need not cut on the lines.  I needed to tape them on to the ¼” plywood to cut out the negative space. Once the negative space was cut out I took a piece of 1/8” ply and painted the puzzle color on that and then glued the ¼ and 1/8” pieces together.  In the end I had a puzzle that had a place on board with its matching color.
The main lesson that I learned is never trust only double sided tape.  Sometime it moves and my double sided tape left a residue.  I fixed that by putting painter’s tape where I taped it.  I also taped around the part to make sur  Over all I did not screw up on too many.  I think I did around 90 puzzles on 34 boards. 




e it did not move.

Saturday, February 24, 2018

Lego Banks

This year our family plans to take the kids to Lego Land.  To continue to reinforce good behavior and some responsibility for this trip, I made them banks.  They are shaped as Lego bricks and made from scrap wood.  I purposely did not put a noticeable plug to get the money out.  The bottom is not glued in, but the joints are tight enough it is very difficult to take them off.  The kids loved them and they are excited to put money in them.


I did make parts for 6 of them.  The other three will have coin bank plugs and the paint will be a little nicer.  I will be selling them when they are complete.  I think they came out well for a weekend project.  I would probably use poplar dowels for the pegs instead of oak if I make more.  

Wednesday, February 14, 2018

Build and Grow



So I tried a build and grow series.  It did not go down in flames but I realized really quickly that I was not going to mass produce them.  It is a pain to line up all the nail holes and predrill everything out.  I understand a little more what it takes to make the build and grow projects.  I would not be able to compete with the product already on the shelf.  I was not a total waste of time though.  Here are some of the key things that I did and learned.


I wanted to make three sets of each.  I created a parts list and listed out all the rips that needed by thickness and totaled how much I would need in each rip.  Sounds difficult but excel and pivot tables make it very easy.  Each piece was cut to the correct length before I even started putting the pieces together.  If my cuts were off then it would not go together.  It was interesting how little lumber it took to make fifteen of these cars.

      Planning and design was also a factor in making these.  I needed to make sure that kids would be able to put them together.  In the end kids are not putting them together because I don’t want to drill all the pilot holes.  I had to think about where the nails would go and could they be pounded in in the location they were in.  There were a couple of instances in the design where I had nails running into each other.




      I used experiences and job knowledge to make these cars more production friendly.  A little note about my work, I work for a cabinet manufacturer.  I did not want to mix my hobby with work which is one of the main reasons I make toys not cabinets.  The cabinets we build are good quality for the price and I would and have put them in my home.  However, I build to a higher quality in personal projects.  So I have tried to keep work and hobby separate as much as possible.  My goal was to produce a fair amount of them and it still is.  When looking at the break down of parts I noticed I had several rips that were an 1/8” apart and all were short lengths.  So I went back through my designs and reduced the amount of rips by a third.  This meant less table saw set ups and longer lineal strips to cut parts out of.


      The last thing that I learned is that I need to follow my plans as well as pay attention to test before drilling everything.  The first front end loader’s shovel is not flat to the ground because I did not put the holes in the correct location.  I thought they were the same as the bulldozer.  The biggest mistake was with the fire truck.  I marked and drill all the holes using the wrong drill bit.  I used 7/32” bit.  I could not fix them and had to remake all of them.  I had to remark and drill 36 holes.

The plan is still to make a lot of them.  I am going back to glue and dowels.  The nice thing is that my kids should be old enough to help me assemble them.  That is what I am looking forward to.

Thursday, October 19, 2017

Rocking Chair

This in not my first rocking chair that I have built, but the first one I designed.  My first ricking chair was from pallet wood and ended up where pallet wood should go: in the fire.  The second was the design my grandfather made.  This one was designed similar to the high chair I recently made.  My seat joiner was a little better on this on one and I did not do mortise and tenon joints.
Overall the rocker is 17 1/2" wide X 22 1/2" tall x 23" long.  It is made out of poplar and the rockers are made form bent lamination.  Bent lamination is taking thin strips of wood and gluing them together.  before the glue dries forcing them into a mold.  When the clue dries the piece takes on the for with a little bit of spring back.  It does not require steam and heat.  I have don this before.  It usually makes a mess so I take clear packing tape and put it on top of the form so the bent piece and form do not stick together.
This go around I was a little more careful on the joinery.  Still not great but better.  It is also helpful that I have a set of nice sharp chisels.  I also cleaned up the dado with a shoulder plane.  I have to justify why I purchased it, right?  The doweled joinery was just for speed.  It still took me forever to make.
I am working on the drawings and procedure now.  I had to make a change to the height because it was too talk.  When doing the dry fit I had my son sit in it.  His feet were three inches off the ground so I took 2 1/2  inches off.  He is almost four so there is the age reference.  That was the only design change on this project.  It came together really well.  My kids want to keep one, my wife says it is defective and I can't give both away.  I was not planning on keeping either.  One is going to be donated to a toy drive.  The other I am not sure yet.

Thursday, August 24, 2017

High Chair


This year I have been trying to improve my skills in joinery and bring in hand tools into my skill set.  With this goal I have purchased some new equipment.  The first was a sharpening system so I can have sharp tools.  After this project I have upgraded my set of chisels to better steel and longer blade for ease of sharpening.
The skill set on this project was hand cut mortises for mortise and tenon joints.  I usually do not use this type joinery because it means hand cut mortises (I am not going to buy a mortising machine) and I have not really been very good at them. I have only done them twice before and both were machine made.  The high chair had 16 mortises.  I attempted to make two.  Only one made it to the end.  Here are some of the things that I learned and took away from the experience:
I set myself the best I could for success.  I watched videos and read information.  I created jigs to make sure my measurements were all the same.  This was a simple block with a groove so I could mark the location to all the mortises and they would all be the same.  All the mortises were the same and only four were in a different location.  Just as I started pounding nails in a 2x4 with my name on it I had 32 mortises that were all the same to practice.
I had sharp tools.  I have previously used chisels and have a set.  They were only sharpened recently for this project.  This is why I had purchased a sharpening system.
I learned that mortises could be cut crooked.  That was the fate of the second one.  I could not square to save my life.  So it turned into blocks.
I understand now what a marking knife is for.  It creates a small cut in the wood that allows the blade of the chisel to sit in.  I am sure it has other purposes but this is the one that I realized.
I learned that a wobbly table is not the best to chop out mortises.  I would love a work bench but I need something that can get out of the way of a car.
This was a challenging project and took a longer than normal time to make.  The plan will not be up for sale at this time.  I will be making one with doweled construction to put on my plans page.  I am glad I did it and a little more confident in making and cut mortises.  I might use them a little more often now.