Showing posts with label Tip. Show all posts
Showing posts with label Tip. Show all posts

Friday, May 29, 2020

Bedroom Furniture: Nightstand


This was a quarantine project.  I had purchased the lumber for the project just before the shelter in place order had been issued.  This is what I would consider fine furniture, which is out of my comfort zone.  I had determined that this bedroom furniture was going to try out more traditional joinery.  This would be mortise and tenons and dove tails.

I worked with my wife on the design and material selection.  We like the simple clean design, so we went with a mission style look.  There were aspects of the aesthetics that were not decided until we started putting the parts together.  My wife liked the red-brown tone, so we went with cherry wood.  Which I am grateful for, because walnut would have been expensive.  Some of the design features I wanted to incorporate a couple of things.  The first was putting in a USB outlet. The second was open/slatted sides. 

The USB outlet was simple, but I made it complicated.  I did not want a cord hanging down the back of the cabinet.  I hollowed out the back of one of the legs and then put in a piece that was cutout in the middle to house the cord.  After the sides were put together, I dilled into the hollowed-out section to pull the cord through.  I realized before drilling that my tenons went through the hollowed-out section, so I needed to rethink where my holes where located.  Installation was harder than I wanted, but easier than expected.  I took string and put it in one hole and with a vacuum and sucked it out the other end.  Then I used the string to pull through the wiring for the USB charging port.  The wires are connected back together and then connections are put together using heat shrink tubes. 

The slatted walls were done by grooving the rails and then putting slats in the groove.  It really was not very difficult, and I simplified a lot of the details.  There are small pieces that needed to be put in the spaces between the slats.  I cut out the curves on the scroll saw so there was a top and bottom to the parts and they were unique to each pair.  I my try to use the router and a template for the next time.




There was a fair amount of learning from this project because this is not a type of woodworking that I do.  Here are some of the key insights:
  • The legs have dimension.  When cutting all my rails I cut them to the width and depth of the nightstand.  I am grateful I figured out the mistake before gluing it all together. It allowed me to practice forming my tenons again.
  • Rough lumber is not as scary as I thought it would be.  I could only get rough lumber and I have never worked with it.  There are some things that I have had to take into consideration.  The first is surfacing it then putting a straight edge on it.  It is not as difficult as a thought it would be.  It is not like the stuff I got from work a few years back. 
  • Tenons don’t need to be supper long.  I made them one inch long.  They were going into 1 ½” legs.  I should have made them 5/8” long.  The tenons were not that difficult; it was the mortises.  They were a pain to clean out.  I will also make them wider than 5/16” next time.  The rails are ¾”+ thick.
  • Epoxy: I don’t know.  It is the first-time using epoxy and it does fill in gaps.  It was a little messy and there was a fair amount of waste.  I have to say the joints are strong.
  • Dove tails are easier to cut on a scroll saw.  I cut a couple of test ones out by hand.  I learned quickly that a cheap coping saw is no good for cutting out waste.  It was a pain and the blade moved everywhere.  It was easy to set the angle and cut on a scroll saw.  It is probably the same on a bandsaw.  Now if I just put the pins and tails on the correct part. 
  • Rulers and tape measures become scales.  I have known this for some time, but it really came out in this build.  I needed to keep with in my constraints of height, width and depth.  Thickness of the boards was when all the saw marks were removed with a planer.  Groove thickness was based on what looked good.  Parts changed as things were put together.  The measuring devices were used more for consistency purposes rather than getting to a specific measurement.  That being said, I still depend heavily on my tape measure.
  • Good joinery makes the assembly a lot easier.  The nightstands came out square and I did not have to worry about making sure all the parts were at the same spacing because all of that was planned for in the joinery.

Overall I am pleased with the look and design.  My wife choose the hardware and it looks better than the ones I was looking at.  Now onto the computer table.

Sunday, June 23, 2019

Painting Toys


Painting Toys The past couple of days have been enlightening for me.  I am a very much anti painting my toys.  I don’t believe wood should be painted.  Let the natural beauty show.  Despite my encouragement to not paint the police car my son still wanted to paint it.  I cringed the entire time and showed him so proper techniques and allowed him to use a “good” brush.  I did put a stop to him adding windshield wipers.  After all my cringing and some helicopter parenting it turned out decent.  The second experience was a package I got from a member of the club.  We shared some plans and he sent me one of the plans he modified.  He added a camper to the mini.  He painted the fenders and honestly I like it.
Now I am faced with a dilemma, to paint or not to paint.  I will still use wood to add color. That is part of this year’s projects.  This year, I might include some painting days for people to paint toys for charity this year.



Monday, May 20, 2019

Hand Planes: Who Would Have Thought




So I have been getting more and more comfortable with hand planes and they are not as scary as I thought they were.  It actually is easier sometimes to grab the plane over sandpaper.  I am not good at flattening board and probably won’t be anytime soon.  My latest discovery is using it when doing panel glue ups.  I would take it off the saw and glue it together.  It was close enough in my opinion.  The glue would “fill-in” the saw marks.  The saw did a good job, but there was always a glue witness line.  I started using the plane to clean the saw marks off the edges in hopes to get a cleaner glue line.  The difference is very noticeable.  The joint is tighter and if the grain is straight and similar it is tough to tell were the piece are put tighter.

Tuesday, January 29, 2019

Refurbishing a Bench


I was given the opportunity to refurbish a bench that my son’s teacher savaged from the trash.  I was thinking that it was going to be a small bench and sanding out some scratches and sharp edges.  It looks like it was a four foot long church pew.  The ends were chewed up by a dog and the seat was pretty scratched up.  I was told that I could just sand it down.  However, it was solid oak and could be a nice bench.  I did not want to just sand it out.

I had to first take it all a part.  It was only screwed together so it wasn’t too bad.  The hardest part was taking out the dowel plugs.  Once it was taken apart the parts that I could use were sanded down. I knew that I needed to replace the seat and the two sides.  Seat was easy.  The sides would need some template work.  That proved to be a little challenging because the edges were chewed up by dogs.  I ended up using edge band to build up the edge and then making a template out of plywood. 
I am not that experienced using a template and a router.  I had the bit but I still managed to mess it up pretty badly.  Here were my two big take a ways from the mistakes:
First is that quick grips do not provide enough clamping power to hold a template in place.  The template moved and I screwed up the top portion of the bench.
Second is that I should have cut the waste closer to the line.  As the router went from end grain to edge grain it took chunks of material with it. 
This is how I fixed it.  I had to cut off the portions that were damaged and put on new pieces.  This time I cut closer to the line and added a relief cuts.  I then used a few more hand screw clamps to secure the template.  It worked much better.
This was going into a classroom so I wanted to put a lid stay on it so that it would not smash fingers.  I bought a set that was rated for 40 lbs.  I should have looked at the install for those before staining.  I underestimated the space I needed.  I had to add a spacer block to make it work.
Staining and assembly went well. I used a minwax stain and let it dry for a week.  The top coat is shellac.  When I was finishing it, there were a couple of people interested.  My wife has also expressed interest in one.

Staining and assembly went well. I used a minwax stain and let it dry for a week.  The top coat is shellac.  When I was finishing it, there were a couple of people interested.  My wife has also expressed interest in one.

Tuesday, July 10, 2018

Shrink Wrap



Just a quick definition, shrink wrap shrinks when in contact with hot air to keep things together.  Stretch wrap stretches and acts like a rubber band to keep things together.  The only reason why I put this in here is because I just learned it a few years back.  I thought the terms could be used interchangeably.  Last year I made several puzzles and used stretch wrap to hold them together (the stuff put on containers of food to put in the refrigerator).  It did not work very well.  This year I ordered some shrink wrap envelopes to play with on the puzzles.  It is amazing how much easier they are to work with.  I do struggle with a one thing, sealing them. I don’t have the correct tools to do it and I don’t feel like dropping a couple hundred dollars on one.  I have about a 75% success rate with a good seal.  When heat is applied the wrinkles form and then go away.  Now I know how to package my puzzles.


Monday, June 11, 2018

Burnout



So I just completed a lot of projects.  My wife came up to me after the second day of finishing and asked, “So are you now done with working in the garage?”  My response was, “Yes, I am going to be assembling all these projects for the next month.”  She responded asking if I was done, done like never going back to woodworking.  I guess she fears that one day that I am going to just burn out and never want to do this again. She is afraid that I am going to burn out.  I can see her point of view.  I just spent two 16 hour days finishing projects.  These projects included 70 cars, 10 trains, 20 tug boats, over 30 puzzle boards, 11 Christmas ornaments, two boxes of donation cars, and miscellaneous projects for friends and teachers.  It was a tough couple of finishing days and it used an entire gallon of shellac.
The question of burnout is real.  I don’t ever want to be done with woodworking.  There is going to be a time when I am going to need to take a couple of years off from the craft show circuit.  I find that more grueling than the woodworking itself.  When that is going to happen, I don’t know yet.  Here are some of the things that I do to keep from burning out on something that I love to do.
·         Keep learning – Don’t be afraid to try something new.  I find challenge keeps the passion and the enjoyment alive.  There are a lot of times that I have projects that just sit around because I am not sure how it will turn out or if I can even perform the task.  If it does not work out then I have created artisanal firewood.  I also find that it is not as bad or tough as I had imagined. 
·         Thinking ahead – Have a new idea being generated as you are working on a project.  It keeps away the idea that there is nothing to do or what to do next.  Some of these ideas will never come to pass but the idea is still there.  I have a notebook where I keep my ideas and I usually have a couple of projects being drawn while working on others
·         Bring it to a new platform – There are now many ways to share your passion.  I have chosen to blog and put items for sale on Etsy.  Last year, I took my projects to local craft fairs.  It was a blast meeting people and talking to them about what I love doing.  There are groups on social media.  Open up and be venerable to comments and critique so that you grow.  
·         Set goals – make sure there is something you are reaching for.  They don’t have to be great just something that you want to do.  Reward yourself when it is reached.  This year was my “build and grow” series and I have these jewelry boxes from last year that I want to get done. 
·         Focus the work load – Don’t take on too many projects or have several going at once.  I know I listed off a lot of projects at the beginning.  These were done over a four month time.  I did the scroll saw work on the week day and the other stuff on the weekend.  Once it was complete it was set aside in a box to finish.  I know now that I need to have more finishing days
·         Engage other people – I have a club that I go to.  There are people that inspire me to do more and improve my skills and there are those that I can help improve and inspire.  Passions don’t become dull and lost when there is a support team helping you and others learning from you.
·         Give – Donate either time or product to others.  Nothing is more inspiring than seeing the joy, awe, and gratitude from someone that you have shared with.  I may be an extremist to this, but I like helping people.  It is part of my woodworking business model.
Burnout is real.  I hope this have given some ideas.

Wednesday, May 23, 2018

Since I got a Hand Plane


Last year, I decided to purchase a couple of hand planes to help me understand how they worked and to allow me a little more flexibility.  I purchased Lie-Nielson low angle jack plane.  I honestly did not think I would use it as much as I do.  I built a storage cabinet and put it, with my sharpening tools, in the back.  It is a rolling cart, so it is not a big deal to get back there, but it is an extra step.
I am amazed how much I use it and how much easier it has made certain tasks.  Just recently, with making a smaller version of a train, I needed to add a flat to the boiler.  Last time I did this I mounted the dowel to a board and cut it on the table saw.  This time I mounted to the table saw and used the fence as a guide.  With a few passes I had a nice flat on the dowel to glue to.
I was making several cars to donate and I had some re-sawn board that had a warp and twist to it.  I did not think much of it because I was cutting them down to about 2” wide by 8” long.  After roughing out the parts I realized I did not run the board through the planer to clean up the band saw marks.  It probably would not have done well because of the warp and twist in the board.  The parts were now too small to run through the planer.  With a couple of passes on the plane and the boards were flat and ready to be cut out on the scroll saw. 
One of the best things that I did was go to a show and get hands on experience with the planes.  I was shown how to set them up and how to take care of them.  I was shown how to sharpen and what the edge of the blade should look like.  I learned some tricks and what to look for.  Best of all, I felt what a tuned plane should feel like and what to expect when using the tools.
 

Wednesday, February 14, 2018

Photocopy Rubbings


So I tried to do a photocopy rubbing on the wood chest of drawers that we purchased for my son.  He is a big Harry Potter fan so I wanted to do one of the Hogwarts crest and one of the Gryffindor crest.  The Hogwarts was in color while the Gryffindor was in black and white.  Looking online they suggest lacquer thinner or acetone.  I purchased lacquer thinner and I had denatured alcohol at home.

My results were, denatured alcohol does nothing.  Lacquer thinner worked a little bit but it was tough to rub out.  I still need to try acetone to see how that works.  The color did not work at all.  I might try the wax paper and inkjet printer if I want to try color again.  If you want to find out more, there is plenty of information on YouTube.  As things work I will continue to update.

Thursday, October 5, 2017

Opps! Mistakes

Sometimes it is refreshing to see that people are human.  We make mistakes, errors and our lives are not as perfect or horrible as we post online.  I make mistakes, and want to share a couple of mistakes I recently made and what I learned from them.
I am working on a child's rocking chair.  Everything was ready to be assembled and doweled into place.  I laid out the first assemblies and glued and clamped them together.  After I had doweled them, I realized that I had switched the two back legs.  With them glued and doweled, I would not be able to take them apart without cutting them.  The good thing is that I only lost two parts and with the dowels in place, the holes were already filled.  It was refreshing to be able to fix a mistake.

I was recently cutting out ornaments to see if I want to make them for next year ornament.  When I cut out thin pieces I stack them so I can cut multiple out at a time.  I also recently ran out of my first big purchase of scroll saw blades.  This meant that I started using the new blades that I had purchased.  These were crown tooth which means that I cut on both the down and up cuts.  They are to give a cleaner finish cut and when they dull, I can flip them over and use the other side.  I am learning that these are good for some applications but not all.  I was cutting the center section of the ornament and about halfway complete when the parts exploded.  I lost for ornaments.  I concluded that I did not have sufficient pressure holding the pieces down so as the blade was cutting upward, it hit a soft spot and broke the piece.  This may have been avoided if I had used a skip tooth blade.



I recently purchased some simple compound patterns.  I have always wanted to try these but did not want to invest in the books at this time.  I figured the patterns were simple enough that I should not have any trouble cutting them.  I did not have the recommended thickness of wood for the pattern.  I was too anxious to wait to pick up some board I reduced the patterns down to the 1 1/4" material I had.  This made the parts really thin and small.  They came out ok.  My blade warped during the cut and the the piece was not as consistent as I had hoped.  After some investigating, I discovered a couple of things.  First was that the blade I was using (crown tooth) does not clear the dust away very well on thick materials.  This would cause a build up in heat causing the blade to warp.  The consistency was cause because I did not clamp the cut parts to keep them in the same place as I was cutting.  I was confident that I could make these cuts easily but there were some things that I needed to learn first.  With a little bit of information I am able to get back to cutting.
Mistakes happen and the best thing that I can do is learn from them.  I hope to continue to post my mistakes so that others can also learn from them.

Tuesday, June 6, 2017

The Right Tools for the Job

I have a project I have been working on for the past few months where the entire purpose was to make mortise and tenons.  It is a high chair.  I don't plan on selling these plans, I will make an easier version to sell.  Being true to my self, I was making two, one to donate, one to sell.  Each chair takes 18 mortises.  So here is what I have learned so far.
First, I have a set of cheap bench chisels.  I have a good sharpening system so I sharpened them up. They worked well for what I can compare it too.  I did notice a couple of things with them.  I have heard that the nice bench chisels are sharp on the sides.  This is to cut the wood cleanly in the corners.  Mine have about an eighth inch of flat on the sides that crushed the fibers.  Not a big deal because no one would see them.
Second lesson was about a marking knife.  I never saw the point of one.  A pencil always seemed to worked for me and a knife line was always hard to see.  I heard that I needed to use a marking knife on mortises so I used an X-acto knife for a marking knife.  The reason is because to edge of the chisel will sit in the knife mark not on a pencil mark.  This helped keep my mortises consistent in size.
The third lesson came from the dry fit.  Mortises need to be cut straight.  I believe it was the first couple that cut were not straight and caused the entire project to be bent out of shape.  I might have been able to fix it, but I cut a mortise on the wrong side of one of the legs which was repairable.  So now I am down to one high chair to donate.
I am having fun learning this, however it does take a lot longer than exposed dowels.  The dry fit showed that it was a much stronger chair.  Hopefully it will be completed in a month.

Friday, April 28, 2017

Taping Glue Up Panels



I read a tip once about adding tape when gluing up panels to help cleaning up squeeze out.  When gluing up panels first put them in the clamps and clamp them tight.  Put masking tape on over the joint.  Remove the panel from the clamp and do it again for the other side.  Cut the tape on the seam of the joint.  Add glue and clamp the panel back up.  After the glue dries peel the tape off and squeeze out come off with it.
I am working on some more cradles and the bottom panel is solid wood.  I have a lot of ¼” material that I would like to use up.  However there is not a lot of material that I can still plane off.  I did not want to deal with removing a lot of squeeze out and planing the board much thinner.  This is why taping the glue up tip came up.
Not a bad tip.  As normal it was not an immediate success.  First was I expected the tape to come right off.  It tore around the squeeze out.  An old sharp chisel was used to take the rest of the tape off.  It came off clean.  I did not have any tear out and I only need to touch up the glue joint.  A word of caution, make sure the tape does not get inside the joint.  That will never come out.  I use blue painter’s tape so that will stick out all down the joint.
I will probably use this tip again.





Tuesday, October 11, 2016

Review of a Scroll Saw Tip

I read a tip to use more of a scroll saw blade.  I probably missed the part where he specified the thickness.  Basically when cutting material only a small part of the blade is being used.  The top portion of the blade is not used.  One way to improve the blade usage is to buy crown tooth configuration.  Once the blade is dull it can be flipped over to use the top of the blade.  The tip was to add a 3/4" thick board to lift the part up and use the fresh top portion of the blade.  I am cheap and figured why not try it to double the life of my blades.
I finished the top a little while ago and finally got around to attach the magnets to the top.  There are a couple of issues that I found where this tip does not work well for me.  The tip works great for 3/8" thick and less material.  I generally work in 1/2" and above.  I do a fair amount of stack cutting also.  The little knob that holds the top of the blade gets really close to the part when raised 3/4".  It will not damage the part but it does not feel good when your finger runs through it.  A 3/8" and thinner piece would not have this is not a problem.  The part in the picture is 3/4" thick.









My basic design was to have a 1/2" piece of plywood with a 1/4" piece of plastic attached.  I know the picture looks like the top is warped but it is not.  I had seen others put a piece of thin board on their tops to reduce friction, others wax their tops.  I had a piece of scrap plastic so I used that on top.  Underneath I used rare earth magnets.  I was not sure how many I needed so I started with two and that was all that was needed.  They hold the top down just fine.
Although the tip does not work for my purposes it was a good tip.  However, I learned why people put thin board to reduce the friction on the plate.  The plastic I had is used on production tables because of its low friction.  It made a huge difference in cutting tight corners and small areas.  The past few times I have been using the top risking minor pain to my right index finger because I like the plastic top so much.  Now I just need to figure out how to put a removable 1/4" plastic top on the saw for my fingers.

Monday, February 8, 2016

Car Carrier

This is probably the single largest toy project I have done.  To be honest I was excited to start working on it and it did not disappoint me when it was finished.  This was supposed to be for Christmas and unfortunately I did not finish it in time so it is now a valentine gift.  I wanted to do a sleeper truck in the semi truck line and I think this stemmed from that desire.  I needed a trailer to go on the back.  It is a rather large toy the truck is 17" long and the trailer is over 25" long. 

So the sleeper cab started it all.  It came out how I wanted it.  The requirement that I has was the sleeper door had to open.  Hardest part of the design was figuring out how the door would stop and not swing both ways.  It honestly took me a long time and several iterations to move the back in 3/8" to use the back of the cab as a stop.  Sometimes the simple answers are the easiest and most often overlooked.  The overall design follows closely to the other cab design just longer.  I have made a few of these so it was not too bad of a build.


The carrier was a little different story for the design and build.  I wanted it to  be able to move and I had a vision of what parts should move and how.  I wanted the little ramps to move and I wanted the back section of the upper ramp to lower down.  the thought of having the entire upper section rotate 90 degrees down felt like cheating to me.  I also wanted the posts to be able to support the upper section without being reinforced.  Some of these presented challenges others were abandoned.
Having the  back section move up and down was a challenge, but after designing the front end loader, I had some pretty good ideas. Making sure the parts had enough of a radius became the hardest part.  However, I did learn that I do not have to radius everything.  There is a block that I originally had a radius that proves to weaken the dowel joint. If I take off the radius it is fine.
The ramps were relatively easy to do however it did take a little bit of had work and a rasp so that they would move up and down.  I was a little worried about the cutout in the raising and lowering arm.  It is stronger than it looks because it is all in line with the grain.
Now there were some compromises that were made with the design.  I figured if I angled the support rails in such a way I would only need two pegs per support rod to keep the upper level ridged.  That did not work out.  There are two support rods that have three pegs in it.  It does not detract from the look at all. 
The other design feature that I missed was the grooves in the rails where the tires roll on.  The original design called for 5/8" deep by 7/16" wide.  I had a 3/8" rabbeting bit for my router.  To make the groove that I wanted, I would need to buy a new nonstandard bit.  I am all about finding a reason purchase new stuff, but I need to be able to design for common tools.  It was a good and quick change in the design.
I posted this to facebook to get feed back on the design and I received a lot of good comments and I would like to address some of them.  There was an overwhelming response that the wheels on the trailer need to be larger.  I tried putting it in the design and it moved things too much.  I could go to two larger wheels instead of three.  I am still mulling through the wheel design.  I also received a lot of comments that the support rails looked like popsicle sticks.  I can make them square without a problem.  The last comment was having the trailer over hand the cab and adding another car.  I ran with this idea for a little while.  Then I watched my kids play with their toys and realized they use the cab to push the trailer around.  If the trailer was overhanging the cab, it would get in the way of the kid pushing the toy.  I have shortened the chassis of the cab so the trailer is closer to the cab so it doesn't look so distant. 
It was a lot of fun to build.  I hope my kids enjoy it as much I did building it.

Friday, January 22, 2016

Lesson Told Now Learned

When I took over the sample shop at the company I currently work for, my first goal was to stock the department with the small tools that they needed so they were not waiting on each other.   One of the recommendations was more clamps.  I asked if they wanted more quick grips because they were faster to use and less cumbersome than the bar clamps.  I was told the quick grips do not have enough holding force for what was required.  I thought that was an interesting comment and tucked it away as a metal note.

Eighty percent of my clamps are quick grip style clamps.  They work just fine for making toys and I have large bar clamps (not quick grip style) for larger pieces.  I am currently working on my kids Valentine gifts.  I received a slab of 10/4 mahogany from a friend cleaning out their garage.  It was water damaged and I was not sure what it was used for so it will not be made into toys.  I figured I could do some through mortises on this project.  Sorry not saying what it is because my wife also does not know and it drives her nuts.  So I made template.  I realized why I do not do a lot of this joinery.  I even cheated and did the template on using CNC.  I cut out most of the material before using a flush trim bit to clean it out.  I started routing and the template moved.  Adjusted it back and made sure my quick grips were really tight and tried again.  It moved again.  I used my bigger quick grips that supposedly have more holding force.  It moved again.  Brought out my furniture screw type clamps.  This time it did not move.  Quick grip clamps are good but not for holding router templates.  The lesson learned a while ago now makes sense.  Looks like I need more clamps.

Monday, June 15, 2015

Glass Nativity

I have done a few of these over the years (actually six).  These will be the last.  They are not as difficult as they were time consuming.  There was also a lot of take away lessons from doing glass etchings.
My dad did the original and several others for other people several years back.  I wanted one about ten years ago.  He had lost the pattern so with a light and paper I copied it.  His was done on tinted glass.  I was told that tinted glass made the etchings look better and the image stand out.  So I went and picked up my glass, etching solution and contact paper.  First lesson: NEVER use easy remove contact paper.  The etching solution lifted the contact paper and I was left with a completely etched glass.  That alone should have been enough to deter me but I had more etching solution left, so I tried it on a much cheaper mirror with the correct contact paper and it worked.  I made two this time because I cut down a full length mirror from Walmart.  I have one and the other is at my in-laws. 
A few years back the one my father did at my parents home broke.  I decided to replace it with a framed mirror one.  Put the contact paper and made all the cut outs and then let it sit.  I found it last year and finished it.  Lesson two: The longer contact paper sits on a surface the more adhesive sticks to the surface.  I think I peeled off pure vinyl and all the adhesive stuck to the mirror.  I used a quart of goof off to remove all the adhesive.  It was given as a Christmas present last year to my parents. My siblings all wanted one.
I had enough etching cream for three more.  I was not going  to buy any more because the stuff is expensive and I really do not like working with glass.  So learning from past experiences I used the contact paper I had left over and did three more in about two weeks.  Lesson Three: As contact paper gets older, the adhesive does not stick well to the vinyl.  This is a little different than lesson two.  As I was cutting out the contact paper for the etched sections not all the glue came off with the vinyl.  leaving a little bit of residue.  I cleaned most of this residue up.  The etching solution did not etch the mirror where there was glue left.  Most of these are small little dots, so to appear to be beauty marks of a handmade piece. 
I also made all the frames for these nativities.  These are beech, stained ebony with a coat of shellac.  The frames came out nice even though I hate to make miter stuff.  I only had one of the three frames be a problem.  So in conclusion, lesson learned:  No more glass etchings.

Monday, June 1, 2015

No truck, not a huge problem

Wood Talk recently did a podcast on how they personally get lumber to their workshops.  Surprisingly, only one had a truck.  I thought it was fitting in what I was trying to figure out.  A couple of years ago I needed to trade in my truck for a minivan.  Our family has been growing and I needed a little more economical car for my day job commute.  So my wife got the minivan and I got her car.  We did not get the minivan that could fit a sheet of ply.  So the question comes up how do I do it.  I did not have to figure out that question until recently.  I just received and order for more tiles, which requires a sheet of MDF.  So I figured I would hope that the lumber yard would be able to cut it down for me, but I had a backup plan if they could not.  I "borrowed" my father's cordless circular saw and brought it with me with some clamps.  (I don't think my dad realizes it is missing yet.)  The lumber yard did not have the ability to cut down the sheets so with a straight edge and the circular saw the board was knocked down to a more manageable pieces.  The lumberyard was happy to provide some assistance and it seemed like this was not the first time a customer has asked to do this.  My dad might get is saw back one of these days.  The only suggestion I have is to bring an extra battery.  They saw does no good with a dead battery.
Now onto the joys of MDF.  I do not typically use MDF in my projects because they are toys.  However MDF is stable, flat and consistent.  My biggest issue working with MDF is the dust that it produces.  I take all the precautions I can when machining it.  My shop vac is hooked up to the saw and running, I have a respirator on and plenty of ventilation.  Still everything was coated in a layer of dust and I was just cutting the parts out.  I think when I do the routing I will do it outside.  It is very messy to work with.

Tuesday, August 5, 2014

Miter Saw Stand, Respirator and Sawdust

It has been a little while since I have posted.  I have been working on a commission job that I am almost finished with.  I tried a few things with it and I don't know if I have an opinion on it yet.  So on to the things that I have learned.
So I finished the miter stand cart and two weeks ago I was using it and must have lifted the wing to hard and ripped it pretty much off.  Particle board is not the best material to screw into especially if it is going to be moving.  I fixed it this past weekend and put in plywood inserts.  this is much sturdier.  I was also able to fix some of the alignment issues that happened on the first build.  My goal is to add at least one extension wing so that I can cut up to six foot lengths.




The fix for the poor strength in particle board

I realize that there is a big push on safety and it seems that more and more of the focus is on removing the dust out of the air.  I do not have a dust collection system in  my shop nor do I have a decent sized shop vac.  This is one of the next tools on my list.  I have a respirator.  However it is only good if it is used.  I use it for finishing and when I am using the belt sander but that is about it.  I figured the sawdust from my other tools was big enough that they pretty much just fell to the ground.  I was listening to a pod cast and the hand tool guy on the show is concerned about dust and uses a respirator when he is working.  I figured I need to rethink my stand on shop dust.
The nice thing that I learned was my respirator comes apart to be cleaned.  I have had the respirator for about 5 years and never cleaned - I did not use it enough either.  It was amazing how much cleaner the mask smelled after it was cleaned.
I have been a little more conscious of the dust that my tools have been putting out.  I am actually surprised how much fine dust is put out by my power tools.  There is a lot and it shows when there is light shining through the shop.  My palm sander was the tool that scared me the most.  Trying to get all the dust off of the long panels for the shelves I am making was ridiculous.  dry rag, wet rag, and tack cloth and still there was more dust.  I am going to be wearing my respirator a little more often.

Monday, December 2, 2013

Christmas Projects

So I have been making a couple of Christmas gifts this year.  My wife says one of them is her favorite thing that I have ever made.  Unfortunately for you, the reader, I am not going to post any pictures of the finished projects because they are gifts.  I will go through the set up.  The first project is a scroll saw project.  I keep hearing to use painter's tape to protect the wood and it is easier to remove the pattern.  I think I will be investing in painter's tape from now on.  Sanding these patterns off would have been a nightmare.
The other part of the scroll saw is that designs can be cut inside of the wood.  Starter holes need to be drilled to to put the blade through.  There were a lot of holes on several parts.  My sons did help drill the holes on some of the parts so their initials also appear on the project.  I cannot take all the credit. 
One thing I did learn about the scroll saw: Don't use it to blow off steam.  It will be even more frustrating.  The blade comes loose, or the board is not cutting where it should be cutting and is all because forcing the board on a thin blade does not make for a good combination.  There is much more finesse and art when using the scroll saw and it does not like being pushed around.

On to the second project.  I am diving more into smaller scale things.  This project I wanted to make several and so I build a jig to make repeatable assemblies.  These things are not as easy as I thought.  The first one I cut with the parts that were going to fit inside the jig.  I assembled the jig with the proper spacing and found out that the parts were too tight to even fit in.
The second attempt I got the spacing right and the first one came out just fine.  I would call this beginners luck. The second, third, and fourth I broke the parts trying to remove them because I was not pulling them straight out.
The third time is a charm, right? well at least it is in this case.  I drilled large holes in the bottom to push the low pieces out.  This proved to be a better way to remove the part without breaking it.  I thought better of drilling all the way through the first time.
There are the setups for my Christmas projects.  Pictures will follow later of the finished projects.