Monday, June 15, 2015

Glass Nativity

I have done a few of these over the years (actually six).  These will be the last.  They are not as difficult as they were time consuming.  There was also a lot of take away lessons from doing glass etchings.
My dad did the original and several others for other people several years back.  I wanted one about ten years ago.  He had lost the pattern so with a light and paper I copied it.  His was done on tinted glass.  I was told that tinted glass made the etchings look better and the image stand out.  So I went and picked up my glass, etching solution and contact paper.  First lesson: NEVER use easy remove contact paper.  The etching solution lifted the contact paper and I was left with a completely etched glass.  That alone should have been enough to deter me but I had more etching solution left, so I tried it on a much cheaper mirror with the correct contact paper and it worked.  I made two this time because I cut down a full length mirror from Walmart.  I have one and the other is at my in-laws. 
A few years back the one my father did at my parents home broke.  I decided to replace it with a framed mirror one.  Put the contact paper and made all the cut outs and then let it sit.  I found it last year and finished it.  Lesson two: The longer contact paper sits on a surface the more adhesive sticks to the surface.  I think I peeled off pure vinyl and all the adhesive stuck to the mirror.  I used a quart of goof off to remove all the adhesive.  It was given as a Christmas present last year to my parents. My siblings all wanted one.
I had enough etching cream for three more.  I was not going  to buy any more because the stuff is expensive and I really do not like working with glass.  So learning from past experiences I used the contact paper I had left over and did three more in about two weeks.  Lesson Three: As contact paper gets older, the adhesive does not stick well to the vinyl.  This is a little different than lesson two.  As I was cutting out the contact paper for the etched sections not all the glue came off with the vinyl.  leaving a little bit of residue.  I cleaned most of this residue up.  The etching solution did not etch the mirror where there was glue left.  Most of these are small little dots, so to appear to be beauty marks of a handmade piece. 
I also made all the frames for these nativities.  These are beech, stained ebony with a coat of shellac.  The frames came out nice even though I hate to make miter stuff.  I only had one of the three frames be a problem.  So in conclusion, lesson learned:  No more glass etchings.

Tower of Blocks

This was a fun little weekend project that took me a couple of weeks to do.  I actually finished the blocks several months ago but decided I needed a carrying case for them.  So that is what I did last week. 

My kids are more interested in knocking the tower down then building a tower.  The blocks are made out of poplar and the box is cherry.  Simple build and did not take that long.  It was also a good way to use the rest of the Shellac that I had before it went bad.


Monday, June 1, 2015

No truck, not a huge problem

Wood Talk recently did a podcast on how they personally get lumber to their workshops.  Surprisingly, only one had a truck.  I thought it was fitting in what I was trying to figure out.  A couple of years ago I needed to trade in my truck for a minivan.  Our family has been growing and I needed a little more economical car for my day job commute.  So my wife got the minivan and I got her car.  We did not get the minivan that could fit a sheet of ply.  So the question comes up how do I do it.  I did not have to figure out that question until recently.  I just received and order for more tiles, which requires a sheet of MDF.  So I figured I would hope that the lumber yard would be able to cut it down for me, but I had a backup plan if they could not.  I "borrowed" my father's cordless circular saw and brought it with me with some clamps.  (I don't think my dad realizes it is missing yet.)  The lumber yard did not have the ability to cut down the sheets so with a straight edge and the circular saw the board was knocked down to a more manageable pieces.  The lumberyard was happy to provide some assistance and it seemed like this was not the first time a customer has asked to do this.  My dad might get is saw back one of these days.  The only suggestion I have is to bring an extra battery.  They saw does no good with a dead battery.
Now onto the joys of MDF.  I do not typically use MDF in my projects because they are toys.  However MDF is stable, flat and consistent.  My biggest issue working with MDF is the dust that it produces.  I take all the precautions I can when machining it.  My shop vac is hooked up to the saw and running, I have a respirator on and plenty of ventilation.  Still everything was coated in a layer of dust and I was just cutting the parts out.  I think when I do the routing I will do it outside.  It is very messy to work with.

Thursday, May 28, 2015

Simi truck Flat Bed Trailer

 

The cab for the truck is basically the same as the dump truck design. I shortened up the chassis and added a hitch.  That is the great thing about a simple design; parts cover multiple designs.


So I thought the flat bed trailer was going to be pretty easy design.  It is a flat bed, no big deal, right?  The rear wheels were going to drive me insane.  My original plan was to cut them out at a 45 degree angle and then figured that for a basic plan that would be a pain to do.  Then it was how to cut the recesses and then how do I cut the base?  I am a power tool woodworker so I really did not want to chisel out an angle.  So I settled on the current plan.  Looks good and relatively simple.

The semi cab is 12 1/2" long and about 7" tall.  The flat bed trailer is 26" long.  It will haul all the vehicles that are part of the construction design right now.  It should accommodate all of my designs. 

Wednesday, May 27, 2015

Bulldozer


This was one of the projects that I really wanted to bring in different thicknesses of wood.  I stayed true to the commitment of standard 3/4" thick lumber.  The hardest part of this entire design was the tread.  I was not expecting this because I knew how I was going to make it from the excavator design.  I was not expecting to figure out what size worked well.  My original plan was  to make the tread taller and not as long.   It would not work and did not look right.  I finally settled on the current size.

The next problem was how it was all going to fit together.  I would love to call it pure genius but in reality it was luck with a little bit of planning.  At first I was going to recess the wheel pegs into the tread, but leaving them out was a perfect location mechanism.  This guaranteed all the wheels the same distance from the ground.




Now the location for the tread front to back I was not so lucky.  First one I placed about a 1/4" from the front.  I added the pegs in the rail to limit the up and down movement.  It limited it too much.  So on the second I though I might get just as lucky with the pegs for the rake in the back.  So I pushed the tread against the tread in the pegs in the back.  The shovel now hits the engine.  I do not know if I am ok with this even though it far better than the first.  Everything else went together smoothly.


It was a fun build and my kids did not understand why they could not play with it after the first dry fit.  I am happy with the design and it is a good addition to the previous designs. 



Tuesday, May 26, 2015

City Trucks Redesign

So I finished the redesign of the city trucks.  I think they turned out a lot better.  Plans will be available on Etsy in the new future for these projects.  I will also be selling the redesign models.  I made these out of oak. 
The Flat Bed Truck


The first thing that  I did was increase the wheel base.  I did this by grooving the side panels and increasing the width of the chassis.  This pushes the wheels to the out on the side side so they do not look so small on the truck.  I also shortened up the bed.  The stakes in the stake bed are now 3/8" instead of 1/4".  I just thought 1/4" was a little too thin for rough play.

The Tow Truck


Similar changes to the flat bed truck.  The wheel base is widened pushing the wheels to the outside.  The tow arm also has more wood need the hook.  This is so it does not split when putting the dowel through the hook.
The Cherry Picker



This was in general too big.  Increased the wheel base and made it duel back wheels.  The bed was shortened and the boom lost about 5" of reach.  It is now more stable and looks better.  The bucket is now just a drilled hole.  This is much easier to cut out then the square it was originally designed.


Monday, May 18, 2015

Cut off Cart

I was kind of tired of my make shift cut off cart.  It was a modified tool cart that I used in my original garage and was no longer needed when I moved into a place with a slightly larger garage.  I was finally done with it and designed this one. 


This was probably one of the fastest projects I have ever done.  From start to finish it took about 4 hours.  It took me about an hour to draw and dimension it out, 20 minutes to program (yes, I used a CNC router), 40 minutes to cut and rout parts, and two hours to assemble.   This cart needed to hold all my small parts that are not yet destined to become blocks and all my dowels.  It serves most of the function I designed it for.  It does not work well with wide stock.  There were a couple of take away points from this project.
The first is that my garage shop does not need to look like a beautiful masterpiece of all that I can do.  Let's face it, I make toys and utility cabinetry.  Yes, some of my stuff is nice but it is nowhere near fine furniture.  This cart is made out of particle board. It is cheap and will will work.  I did not bother hiding grooves and glue squeeze out.
I was not looking for quality work.  I was confident that the CNC router did its job accurately and I did not have to worry about things fitting together.  I wanted to counter sink the screws but could not find my bit.  The joys of kids.  Screws stick out a little and that is ok.  I have found my countersink bit and am not going to go back through to sink the heads of the screws.
Material was not really a concern.  If I had my choice I would make it out of plywood.  I did not need to so why spend the money.  This was going to be for my eyes only anyway.  I needed it to support the weight so 5/8" particle board was sufficient.
I knew what I wanted this cart to do.  It was to hold off fall and my dowels.  It does that.  Looking back at the design I may have wanted to make it 2" wider to handle wider stock.  Not a big deal.  I am please with the way it turned out.
The last take away, more on the light side, was make sure there is plenty of glue in the bottle.  I had about a 1/3 of a bottle of glue and figured that was enough.  I was wrong, just barely.  I was gluing the sides to the partitions (last step) and on the last glue line and ran out.  I was shaking the bottle and trying to get every last drop out before the glue skins over.  The good thing is that I buy glue by the gallon so it was just a refill thing.  I was lucky.

Glad this project is complete.  Now I need to make a sanding cart (my next shop project).  This one is going to take a little longer.